Max Torque Driven 20 Series - Outboard | 400806

Home > Go Kart Parts > Go Kart Torque Converters > Max Torque Driven 20 Series - Outboard

Max Torque Driven 20 Series - Outboard

Part Number:400806

Availability:In Stock

Location: 0600.02.04, SR.2.B.7 ;

7 Review(s)

5/5 stars

Your Price: $64.95

Quantity

Description
Specs

Customer Reviews
Manuals & How-To-Guides

Product Specs:

Max-Torque 20 Series Driven
3/4" bore with 3/16" Keyway
7" OD
This unit should be mounted so it can float on the jackshaft to stay aligned with the driver.
Mainly used on Yerf-Dog, Thunder Karts, USA Industries, Murray & Yellow Jacket

View All Reviews

Did you find this helpful?

Reviewed by: Darius McCollum on 4/6/2023

Did you find this helpful?

Reviewed by: Anabel Warren on 10/16/2022

Did you find this helpful?

Reviewed by: Marcellus Stahl on 9/2/2022

Did you find this helpful?

Reviewed by: Stephanie Wise on 3/23/2021

Did you find this helpful?

Reviewed by: Landen Hayes on 5/3/2019

What Series Comet Torque Converter Do I Have?

20 FAQs on Torque Converters

Torque Converter User Guide

About your Max-Torque Variable Speed Torque Converter Drive System
- Your variable speed drive system consists of a driver, a driven and a 26 degree symmetric V type belt.
- The driver unit consists of two 13 degree variable pitch sheaves mounted on the engine crankshaft. As the RPMs increase above the idle speed of 1850 RPM the unit is activated by centrifugal force. The floating sheave of the driver is forced inward as the RPMs increase. Contact is made with the belt forcing it to move upward on the driver sheaves and downward on the driven sheaves. The driven unit is two 13 degree variable pitch sheaves with 7 inch diameters that are mounted on the jackshaft. The driven unit has been designed to float on the jackshaft. It should not be fixed. Once the belt is aligned with the driver, all float with the driver will be towards the engine.
Engine Ranges
- At Idle Speed- The driver unit is disengaged. No tension on the belt. The driver is immobile.
- At Low Speed- With acceleration, the driver sheaves begin to close. The tension on the belt moves the driver
- At Middle Speed- With continual acceleration, the driver sheaves move to close as the driver sheaves move to open
- At High Speed- The driver sheaves are closed. The belt has attained maximum height on the driver and traveled the maximum downward distance on the driven
- Your complete unit must be mounted on parallel shafts with a desired center distance no greater than 6 13/16 (6.8125) inches. After it is centered at idle the driven unit must have at least 3/8 of an inch inward float to properly align with the driver unit. DO NOT USE UNIT WITHOUT COVERGUARD IN PLACE. Pieces may not be interchanged with any non Maxtorque components.
Maintenance of your Torque Converter
- Maintenance will include proper cleaning and lubrication of the driver and driven bushings. This should be performed at least semi-annually. Weekly inspections of the three wear plugs is recommended before damage occurs to the driven unit (larger pulley). Replacement of the wear plugs can prevent costly overhaul of the driven unit.
- To properly lubricate the driver unit, it must be cleaned first. After dis-assembly, just wipe out excess dirt with a clean rag. After the driver unit has been cleaned, apply Max-Torque's dry lubrication to the angled lop of the weights, the four lobes of the spline, and the hub of the sheave where the bushing rides. Wipe any excess lubrication off the sheaves. Clean the driven unit at the same time you clean the driver. Use the same dry lubricant on the driven unit, the bushing, the spring, the ramps, and wear plugs. When placing the driven unit back on the jackshaft, only use the 2.7" key provided.
- Upon cleaning the driven unit, if the wear plugs appear worn or missing, they must be replaced. Failure to do this will result in the cam unwinding the spring.
- Keep the belt dry when running. Do NOT get oil or lubrication on the belt or the in-side of the sheaves where belt contact is made or excess slip will occur. Oil/lubrication must be cleaned off prior to using your kart or you will destroy the belt.
- Only use the belt provided, it has been designed to open the driven unit sheaves to the proper dimension for the highest speed range. If your belt shows signs of uneven wear, it may be due to the engine crankshaft and jackshaft not being aligned perfectly parallel. -Your variable speed drive system should be mounted on parallel shafts - the driver on the engine crankshaft parallel to the driven on the jackshaft. In idle, the belt should be straight in the sheaves and square to the crankshaft and jackshaft. DO NOT FLOAT the driver unit on the crankshaft. Only the driven unit floats on the jackshaft to align with the driver clutch as it attains the various speed ratios. The sprocket mounted on the jackshaft must be aligned parallel with the rear sprocket.
- Misalignment can cause damage to the chain. The driver unit must always be in neutral to move in reverse. Any backwards movement while your Variable Speed Drive System is engaged may cause damage, such as unwinding the spring in the driven unit, breaking the wear plugs or damaging the cams. This problem is not covered under The Max-Torque Factory Warranty.