Account
0 Item
(937)-526-9544
(937)-526-9544
0 Item
Account
Parts Breakdowns
How-To-Guides
Blog
Catalog
Go Kart Parts and Kits
Racing Kart Parts
Drift Trike Kits and Parts
Mini Bike Parts and Kits
Vintage Motorcycle Parts
Off-Road Karts and UTVs
Shop Parts by Go-Kart Brands
Outdoor Power Equipment Parts
Stens Power Equipment Parts
R.C. Vehicles and Parts
Models, Toys, & Hobbies
Guitars, Kits and Parts
Events
Supplements, Protein & More
How-To-Guides
Parts Breakdowns
Yerf-Dog
TrailMaster
Hammerhead
American LandMaster
Baja Motorsports
Manco Karts
Carter Bros. Karts
A.C.E. Karts
Comet Torq-A-Verters
Blog
Catalog
|
Categories
Go Kart Parts and Kits
Racing Kart Parts
Drift Trike Kits and Parts
Mini Bike Parts and Kits
Vintage Motorcycle Parts
Off-Road Karts and UTVs
Shop Parts by Go-Kart Brands
Outdoor Power Equipment Parts
Stens Power Equipment Parts
R.C. Vehicles and Parts
Models, Toys, & Hobbies
Guitars, Kits and Parts
Events
Supplements, Protein & More
Home
>
Go Kart Parts
>
Go Kart Engines and Components
> Billet Stock Rod for Honda GX160/ 200, 196cc Clone
Billet Stock Rod for Honda GX160/ 200, 196cc Clone
Billet Stock Rod for Honda GX160/ 200, 196cc Clone
(3.303" x 1.180" x .709")
Part Number:
A6270
Manufacturer's Part Number:
6270
Availability:
In Stock
Location:
0400.22.02, SR.1.B.4
;
6
Review(s)
5
/
5
stars
Price
Your Price:
$79.95
Quantity
Add to Cart
Write a Review
Add to Wish List
Email a friend
Description
Customer Reviews
Recommended Products
ARC stock length billet rod with bearing inserts for the GX200 & GX160 or the 196cc (Clone)
Product Specs:
3.303" center-to-center for a 1.180 rod journal and .709" wrist pin.
For use with the stock crankshaft and stock style (dished or flat top) piston in modified engines.
Uses ARC's custom manufactured bearing inserts and ARP rod bolts manufactured specifically for ARC.
ARC has the only forced oiling scoop dipper rods available for these engines providing superior lubrication at the bearing journal.
Rod bolt torque: 170 in/lbs lubricated
Installation Instructions:
To install your ARC rod you will need a 12 point 1/4" socket and a QUALITY inch pound torque wrench. You will need an outside micrometer, dial bore gauge or plasti gauge, and oil.
Measure the crank pin diameter with the outside mic, it should measure 1.180" +/-.0005". Measure in several spots to insure roundness. If out of round more than .0005" it probably should be replaced. The crank pin finish should be smooth to the touch.
When disassembling the rod notice on the side of the rod with the part number there are two dots next to the separation point of the beam and cap. These dots help to re-orientate the cap and beam when assembled. The side of the rod with the part number engraved will always face the side cover side.
Make sure the bearing and rod serrations are clean and install the bearings. Lubricate the rod bolt threads and hand tighten the bolts. Using the torque wrench tighten the bolts to 60" lbs. Alternate each side to increase the torque by 20" lbs at a time until you reach 150"lbs. Then loosen the bolts and repeat the torque process. this helps seat the rod bearing especially on a new rod. Measure the bore with your dial bore gauge opposite the parting lines. If using plasti gauge you will have to install the rod on the crank and use in accordance the plasti gauge instructions.
The rod bore should measure 1.183 +/.0005". With plasti gauge you are looking for about .003" clearance. From .0025-.0035" clearance is acceptable. Anything outside that dimension please call 800-521-3560 for recommendation.
Once clearance is set apply oil to rod, crank, and wrist pin and install this time torque to 170"lbs.
Improperly torquing rod bolts is one of the most common causes of rod failure.
Refer to instructions shipped with all rods
View All Reviews
Did you find this helpful?
1 of 1
Found Helpful
Reviewed by:
Broderick Dant
on 2/14/2017
5
/
5
Did you find this helpful?
1 of 1
Found Helpful
Reviewed by:
Broderick Dant Â
on 2/14/2017
5
/
5
Did you find this helpful?
1 of 1
Found Helpful
Reviewed by:
Broderick Dant ÂÂ
on 2/14/2017
5
/
5
Did you find this helpful?
Reviewed by:
Ryan Wood
on 9/3/2020
5
/
5
Did you find this helpful?
Reviewed by:
Jamie English
on 2/19/2019
5
/
5
Accessories
Billet Flywheel for 196cc Honda / Clone
(6)
Your Price:
134.95
(A6619) |
In Stock
Billet Rod Bearing for Honda GX200/196cc Clone
(6)
Your Price:
27.95
(A6394) |
In Stock
Related Items
Cylinder Head for Honda GX340 & GX390 / Clone 11HP & 13 HP Engine
(4)
Your Price:
21.95
(JF390.2) |
Briggs Animal Throttle Kit
(4)
Your Price:
24.95
(KM609) |
In Stock
Valve Cover Gasket for 13HP Clone / GX390 Engine
(2)
Your Price:
7.95
(ST_475-450) |
Special Order
Crankcase Gasket for 13HP Clone / GX390 Engine
(2)
Your Price:
8.95
(ST_470-236) |
In Stock
Gasket Set for Honda GX390 13HP Engine
(1)
Your Price:
31.95
(ST_480-403) |
Special Order
Predator 212cc Ghost Upgrade Accessory Kit
Available in #35 or #219 Chain Pitch
(0)
Your Price:
285.95
(KRLV-EGK0505 or KRLV-EGK0505-219) |
In Stock
Recently Viewed Items
Quick View